Masimo Radical Signal Extraction Manuel de l'opérateur télécharger pdf (Page 19)

3-4 Radical-7 Color Display Signal Extraction Pulse Oximeter Operator’s Manual Radical-7 Color Display Signal Extraction Pulse Oximeter Operator’s Manual 3-5

OPTION DEFAULT SETTING

TREND PERIOD

Set to 1 Hr.

LOW SpO

ALARM LIMIT

Set to 0

SpMet HIGH/LOW ALARM LIMIT

Set to High: 3.0/Low: ---

SpCO HIGH/LOW ALARM LIMIT

Set to High: 45/Low: ---

SMART TONE

Set to Yes

ADULT/NEO (HOSPITAL DEFINED) SETTINGS

The following table outlines settings that may be defined by the hospital. If enabled (via a

password protected screen, see Section 4 Password Operation), these settings will return

to pre defined values after a power cycle. This mode is indicated by “Mode Adult” or “Mode

Neo” on the Alarms menu. See Section 4, Operation for details on enabling and setting

these parameters.

OPTION

CUSTOM SETTING

(DEFAULT)

ADULT / NEO SETTING

(PRE DEFINED)

SPO

HIGH/LOW ALARM

LIMIT

Set to High: ---/Low: 90

Same settings

PULSE RATE HIGH/LOW

ALARM LIMIT

Set to High: 140/Low: 50 BPM

SpMet HIGH/LOW ALARM

LIMIT

Set to High: 3.0/Low: ---

SpCO HIGH/LOW ALARM

LIMIT

Set to High: 45/Low: ---

ALARM SILENCE

Set to 120 seconds

ALARM VOLUME

Set to 3

ALARM DELAY

Set to 5

Satshare Setup

The Radical-7 Pulse CO-Oximeter has been proven to be accurate during patient motion

and low perfusion conditions. Saturation and pulse rate values from the Radical-7 Pulse

CO-Oximeter may be displayed on a multiparameter monitor through the SatShare fea-

ture.

The SatShare feature provides an ideal, simulated waveform corresponding to the mea-

sured saturation and pulse rate values determined by the Masimo SET technology. This

waveform may be used to display these values on multiparameter monitors through the

multiparameter monitor’s oximetry sensor or input connector.

It is recommended that the Radical-7 Pulse CO-Oximeter is positioned close to the mul-

tiparameter monitor with the Radical-7 Pulse CO-Oximeter screen visibly displaying the

plethysmographic waveform and the saturation and pulse rate measurements.

CAUTION: SIMULTANEOUS USE OF SATHSARE AND SERIAL PORT IS NOT

SUPPORTED.

SATSHARE SETUP

1. Select the SatShare cable that is appropriate for the multiparameter monitor that

is being connected. Check the Masimo web site at www.masimo.com for the lat-

est list of available SatShare cables and validated instruments.

2. Connect the labeled end of the cable to the SatShare Cable Connector port on

the back of the Docking Station. Tighten the connector screws for a secure con-

nection.

3. Connect the other end of the SatShare cable either to the sensor connector of

the multiparameter monitor’s SpO

cable or directly to the SpO

connector on the

monitor.

4. Verify that the Radical-7 Pulse CO-Oximeter recognizes the correct cable. The

name of the SatShare cable will be displayed on the LCD screen when the

SatShare mode is functional.

5. Set the multiparameter monitor’s high and low saturation and pulse rate alarm

limits as appropriate.

6. Set the multiparameter monitor’s averaging time to the lowest setting (i.e. fastest

response). The Radical-7 Pulse CO-Oximeter’s ideal waveform necessitates the

need for additional averaging by the monitor. If the multiparameter monitor’s aver-

aging time is not changed, the time to display physiological changes in saturation

on the monitor will be increased with SatShare. However, the delay can be mini-

mized by reducing the multiparameter monitor’s averaging time.

7. While in the SatShare mode, if there are any significant discrepancies between

the readings from the Radical-7 Pulse CO-Oximeter and those on the monitor dis-

playing the values obtained from SatShare, the values reported by the Radical-7

Pulse CO-Oximeter are to be considered the correct values.

8. To use the Radical-7 Pulse CO-Oximeter with SatShare while it is not connected

to AC power, set the Power Save parameter in the General menu to “No” and

refer to Section 4-Operation. Please note that if the Radical-7 Pulse CO-Oximeter

is used in this mode, the length of time the Radical-7 Pulse CO-Oximeter can

operate on battery power will be significantly diminished.

setup

l E

tra

cti

-O

asim

SET

10/11/06

12:23:11am

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 54 55

Commentaires sur ces manuels

Pas de commentaire

Masimo Radical Signal Extraction Manuel de l'opérateur Page 19

Commentaires sur ces manuels