Masimo Radical Signal Extraction Manuel de l'opérateur télécharger pdf (Page 13)

2-4 Radical-7 Color Display Signal Extraction Pulse Oximeter Operator’s Manual Radical-7 Color Display Signal Extraction Pulse Oximeter Operator’s Manual 2-5

system description

SIGNAL IQ

The Signal IQ shows the acquired signal quality and the

timing of the pulse. A tall vertical line indicates a high qual-

ity signal, while a small vertical line indicates a low quality

signal. The Signal IQ may will be displayed as a single,

pulsating bar in the Numbers mode.

BRIGHTNESS

LEVEL

The Brightness level icon displays when utilizing the

Backlight/Contrast button.

3.00

PERFUSION

INDEX

The Perfusion Index indicates numerically the percentage of

pulsatile signal to non-pulsatile signal (pulse strength).

APOD

SENSITIVITY

The MAX or APOD™ sensitivity icon is shown on the

Radical-7 display to indicate if the Radical-7 is set to oper-

ate in Normal sensitivity, Maximum sensitivity or Adaptive

Probe Off Detection mode

140

PULSE RATE

ALARM LIMITS

DISPLAY

The Pulse Rate Alarm Limits Display shows the upper

and lower pulse rate alarm limits. When an alarm limit is

reached or exceeded, the pulse rate value and the violated

limit flashes.

FastSat

FAST S AT

The FastSat

label is shown on the Radical-7 display when-

ever the Radical-7 is set to operate in the FastSat mode.

PULSE RATE

The Pulse Rate Measurement Display shows the patient’s

pulse rate in beats per minute. The upper and lower pulse

rate alarm limits are also displayed next to the pulse rate

measurement. The pulse rate is calculated and the display

is updated at a frequency of once per second.

Philips VueLink

SERIAL

OUTPUT MODE

The Serial Output Mode displays the selected output interface

when interfaced with the Docking Station. and connected to the

serial port with the selected Satshare cable.

* For instruments that include SpMet and SpCO parameters: the SpMet and SpCO

parameters will be grayed out in the display screen if a patient cable is not attached or a

non-Rainbow sensor is being used.

NOTE: The Pulse CO-Oximeter display view will be different without the optional SpCO

and SpMet options.

system description

2-4

SpCO ALARM

LIMITS DISPLAY

The SpCO Alarm Limits Display shows the upper and lower

alarm limits. When the measured value is outside of the

alarm limits, the SpCO measurement display flashes and an

alarm will sound

PULSE

WAVEFORM

DISPLAY

The Pulse Waveform Display shows the acquired plethysmo-

graph waveform. The pleth waveform is scaled with signal

strength. Signal strength is defined as the relation of arterial

pulsatile signal to the non-pulsatile signal component.

BATTERY

STATUS

INDICATORS

The Battery Status Indicators show the capacity of the

Radical-7 Handheld and optional Docking Station batter-

ies. The indicator flashes when less than 15 minutes of bat-

tery life is left and the battery needs to be recharged. The

Docking Station Battery Status indicator is not shown when

the optional Docking Station battery is not present.

TOUCH KEY

CONTROL

BUTTONS

Press a Touch Key Control Button to select the correspond-

ing touch key icon. See Section 4, Touch Key Control

Buttons and Icons for more details.

BACKLIGHT

BUTTON

Press the Backlight Button to change the illumination level

of the backlight. With the AC line power connected, four

levels of illumination are available (in addition to the no

illumination level). In the Handheld mode, three levels of

illumination are available (again in addition to the no illumi-

nation level). Use the lowest illumination for most efficient

battery usage.

ALARM SILENCE

BUTTON

Press the Alarm Silence Button to temporarily silence

patient and low battery alarms. Press the Alarm Silence

Button when the SENSOR OFF message is flashing (i.e.

the sensor is removed from the patient) to acknowledge

the end of monitoring. In this state, all further alarms are

suspended until the Pulse CO-Oximeter starts measuring

SpO

, SpMet, SpCO and pulse rate again.

Note: System failure alarms can be silenced by pressing

the Power/Standby or Alarm Silence Button. If the Power/

Standby Button does not silence the system fault alarm,

press the Alarm Silence Button

SPEAKER

The speaker indicates audio alarms. Care should be taken

not to cover the speaker and muffle the audible alarm

volume.

PATIENT CABLE

CONNECTOR

Connect a patient cable or a direct cable sensor into the

Handheld Radical-7 by plugging the cable into the Patient

Cable Connector. Use only Masimo compatible sensors

and cables with this oximeter. See Section 8, Sensors and

Patient Cables for more details.

POWER/ON/OFF

BUTTON

Press the Power/On/Off Button to turn the instrument on.

Press, hold the button for more than 2 seconds and then

release the button to turn the instrument off.

APOD

REND

GRAPH

MAX

TOUCH KEY

ICONS

The Touch Key Icons indicate the software menu items that

can be selected through the Touch Key Control Buttons.

Pressing a Touch Key Control Button next to an icon selects

the option.

10/11/06 12:23:11am

TIME AND DATE

INDICATOR

The Time and Date Indicator displays the current time and

date. The time is displayed in 12 or 24 hour format. The date

is displayed in dd/mm/yy or mm/dd/yy format. Select the

date and time display formats in the Clock menu.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 54 55

Commentaires sur ces manuels

Pas de commentaire

Masimo Radical Signal Extraction Manuel de l'opérateur Page 13

Commentaires sur ces manuels